qconfirm-check - request delivery confirmation under qmail
|qconfirm-check [-m] [-n] [-b] [-d] [-i bytes] [-t timeout] [prog]
(perhaps) requests delivery confirmations from the envelope sender to allow
further processing in the .qmail file.
qconfirm-check can operate either sender-based
or message-based, see below for sender mode and message mode.
an empty envelope sender and the envelope sender <#@> are allowed by default.
WARNING: If you create a .qmail file to enable qconfirm-check, make sure
to also add a line specifying delivery to your normal mailbox.
qconfirm-check runs in sender mode, messages from known envelope senders
are accepted without a confirmation, and immediately allowed to be processed
further in the .qmail file.
qconfirm-check defers messages from unknown envelope
senders temporarily, and sends a confirmation request message to the sender.
The original message and all newer messages from the same sender will be
deferred temporarily until a reply to the confirmation request is received.
A message bounces if queuelifetime has expired. New messages from the same
sender do not result in new confirmation requests.
Once an envelope sender
has confirmed a delivery, qconfirm-check treats this envelope sender as
If qconfirm-check runs in message mode (option -m is set),
each single message needs to be confirmed to be allowed to be processed
further in the .qmail file.
A message bounces if queuelifetime has expired.
- message mode. qconfirm-check identifies the message by its inode.
Each message must be confirmed before it is allowed to be processed further
in the .qmail file. Without this option qconfirm-check runs in sender mode.
- no acknowledge. Do not acknowledge the receipt of a reply to a confirmation
- bad. Only works in sender mode. After checking if the envelope
sender is currently pending or ok, check if it is matched as bad.
match. Only works in sender mode. Use extended envelope sender addresses
matching for domains and subdomains. This applies for matching senders for
ok and bad.
- -i bytes
- include the top bytes bytes of the sender's message at
the bottom of a confirmation request or acknowledgement. Default is 8192.
- -t timeout
- Set the timeout for sending confirmation requests as reminders
to timeout seconds. Unaccepted and unconfirmed messages are held in the
queue. Whenever qmail tries to deliver the message, qconfirm-check checks
if timeout or more seconds have expired since a confirmation request was
sent. If so, qconfirm-check again sends a confirmation request as reminder.
If timeout is zero, only one confirmation request per message or sender
is sent and no reminders. Default is 345586 (ca. four days).
- prog can
be omitted or consists of one or more arguments. If prog is set, qconfirm-check
runs prog just before requesting a delivery confirmation. If prog exits
zero, qconfirm-check allows the message to be processed further in the .qmail
file without a confirmation and exits immediately. If prog exists 111, qconfirm-check
exists 111 immediately. In all other cases qconfirm-check continues and requests
a delivery confirmation.
- The environment variable
QCONFIRM_MAILNAME overrides the default mailname in the from header of
confirmation requests and acknowledgements (qconfirm).
environment variable QCONFIRM_EXT overrides the default extension used
for receiving message confirmations (qconfirm-).
- This environment
variable must be set if the mail address you run qconfirm for is controlled
through qmail's virtualdomains. It must be set to the prepend part of the
corresponding entry in /var/qmail/control/virtualdomains plus a dash at
- The environment variable QCONFIRM_DIR overrides the
default location of the user's qconfirm directory (.qconfirm/).
- The environment variable QCONFIRM_ACCEPT overrides the default invocation
of qconfirm-accept(1) in automatically created .qmail files (qconfirm-accept).
- If QCONFIRM_ACCEPT_PROG is set, its value is used
as prog argument to qconfirm-accept(8) in automatically created .qmail files.
qconfirm(1), qconfirm-accept(1), qconfirm-conf(1), qconfirm-return(1),
qconfirm-control(1), qconfirm-cdb-check(1), qconfirm-cdb-update(1)
Gerrit Pape <email@example.com>
Table of Contents