Postfix Before-Queue Content Filter
WARNING WARNING WARNING
The before-queue content filtering feature described in this document is suitable only for low-traffic sites. See the "Pros and Cons" section below for details.
The Postfix before-queue content filter feature
As of version 2.1, the Postfix SMTP server can forward all incoming mail to a content filtering proxy server that inspects all mail BEFORE it is stored in the Postfix mail queue.
The before-queue content filter is meant to be used as follows:
The before-queue content filter is not to be confused with the approach described in the FILTER_README document, where mail is filtered AFTER it is stored in the Postfix mail queue.
This document describes the following topics:
The before-filter Postfix SMTP server receives mail from the Internet and does the usual relay access control, SASL authentication, RBL lookups, rejecting non-existent sender or recipient addresses, etc. The before-queue filter receives unfiltered mail content from Postfix and does one of the following:
The after-filter Postfix SMTP server receives mail from the content filter. From then on Postfix processes the mail as usual.
The before-queue content filter described here works just like the after-queue content filter described in the FILTER_README document. In many cases you can use the same software, within the limitations as discussed in the "Pros and Cons" section below.
In the following example, the before-filter Postfix SMTP server gives mail to a content filter that listens on localhost port 10025. The after-filter Postfix SMTP server receives mail from the content filter via localhost port 10026. From then on mail is processed as usual.
The content filter itself is not described here. You can use any filter that is SMTP enabled. For non-SMTP capable content filtering software, Bennett Todd's SMTP proxy implements a nice PERL/SMTP content filtering framework. See: http://bent.latency.net/smtpprox/.
This is configured by editing the master.cf file:
/usr/local/etc/postfix/master.cf: # ============================================================= # service type private unpriv chroot wakeup maxproc command # (yes) (yes) (yes) (never) (100) # ============================================================= # # Before-filter SMTP server. Receive mail from the network and # pass it to the content filter on localhost port 10025. # smtp inet n - n - 20 smtpd -o smtpd_proxy_filter=127.0.0.1:10025 -o smtpd_client_connection_count_limit=10 # # After-filter SMTP server. Receive mail from the content filter # on localhost port 10026. # :10026 inet n - n - - smtpd -o smtpd_authorized_xforward_hosts=127.0.0.0/8 -o smtpd_client_restrictions= -o smtpd_helo_restrictions= -o smtpd_sender_restrictions= -o smtpd_recipient_restrictions=permit_mynetworks,reject -o smtpd_data_restrictions= -o mynetworks=127.0.0.0/8 -o receive_override_options=no_unknown_recipient_checks
Note: do not specify spaces around the "=" or "," characters.
The before-filter SMTP server entry is a modified version of the default Postfix SMTP server entry that is normally configured at the top of the master.cf file:
The after-filter SMTP server is a new master.cf entry:
By default, the filter has 100 seconds to do its work. If it takes longer then Postfix gives up and reports an error to the remote SMTP client. You can increase this time limit (see configuration parameter section below) but doing so is pointless because you can't control when the remote SMTP client times out.
Parameters that control proxying:
The before-filter Postfix SMTP server connects to the content filter, delivers one message, and disconnects. While sending mail into the content filter, Postfix speaks ESMTP but uses no command pipelining. Postfix generates its own EHLO, XFORWARD (for logging the remote client IP address instead of localhost[127.0.0.1]), DATA and QUIT commands, and forwards unmodified copies of all the MAIL FROM and RCPT TO commands that the before-filter Postfix SMTP server didn't reject itself. The SMTP proxy server should accept the same MAIL FROM and RCPT TO command syntax as the Postfix SMTP server. Postfix sends no other SMTP commands.
The content filter is expected to pass on unmodified SMTP commands from a before-filter Postfix SMTP server to an after-filter Postfix SMTP server that usually listens on a non-standard port. When the filter rejects content, it should send a negative SMTP response back to the before-filter Postfix SMTP server, and it should abort the connection with the after-filter Postfix SMTP server without completing the SMTP conversation with the after-filter Postfix SMTP server.
More detail on the postfix-to-proxy interaction is in the section titled "Transparency".
The before-filter Postfix SMTP server forwards the MAIL FROM, RCPT TO and DATA commands that it has approved, but it does not forward other commands such as TLS or SASL commands. It can therefore not be transparent.
The real-time content filter, on the other hand, has to be transparent. In order to support non-transparent real-time content filters, Postfix would have to reconcile the before-filter Postfix ESMTP feature set with the feature set that Postfix receives from the real-time content filter.
Therefore, the Postfix SMTP server cannot be transparent with respect to the before-queue content filter.